|
HBA's & Switches
Emulex HBA's
 Sunstar Company
is proud to be an Emulex partner!
LP9002DC LightPulse 2Gb/s Dual
Fibre Channel PCI Host
Bus Adapter
 |
Major Features
- Simultaneous full duplex 2 Gb/s Fibre Channels deliver up to
400MB/s
- Automatic speed negotiation
- Full fabric support using F_Port and FL_Port connections
- Onboard hardware context cache for superior fabric performance
- Support for concurrent use of multiple concurrent protocols (SCSI
and IP)
- Full support for both FC service class 2 and 3
- Support for FC-Tape (FCP-2) devices
- 64-bit 66MHz PCI 2.2 compatibility
- End-to-end parity protection for high data integrity
- Robust suite of software including IP and storage protocols under
Windows 2000, Windows NT, HP-UX, Linux, NetWare, AIX and Solaris
- Optical small form factor (LC) interface support
|
|
Description The LP9002DC Dual
Channel PCI host bus adapter offers two independent 2Gb/s Fibre Channel
HBA interfaces in a single PCI slot. It delivers exceptional performance
through the use of two Emulex Centaur ASICs, two 266MIPS onboard
processors, high speed buffer memory and a high performance 64 bit 66
MHz PCI bridge. The LP9002DC features automatic speed negotiation
capability which allows complete compatibility with existing 1Gb/s Fibre
Channel SANs, while allowing seamless upgrades to higher speed 2Gb/s
SANs.
The LP9002DC architecture is based on two of Emulex's high
performance 2Gb/s HBAs integrated into one board with a PCI bridge to
provide bus compatibility with PCI 2.2 based systems. This provides the
flexibility and broad interoperability needed for complex, highly
scalable SANs. The LP9002DC provides a combination of features,
including switched fabric support using F_Port and FL_Port connections,
full-duplex data transfers, high data integrity features, support for
all Fibre Channel topologies and support for service classes 2 and 3, in
a dual channel HBA.
The LP9002DC also features sophisticated hardware that provides
superior performance in SANs, delivering low latency and high throughput
in switched fabric, arbitrated loop and clustered environments. Support
for fiber optic cabling is provided through embedded small form factor
(LC) optical interfaces.
Driver Support
A rich suite of software support complements the LP9002DC, including
storage protocol (SCSI), network protocol (IP) and multi-protocol (SCSI
& IP) operation. These enable advanced storage area network (SAN)
implementations in Windows 2000, Windows NT, HP-UX, Linux, NetWare, AIX
and Solaris environments. All drivers are also fully compatible with the
Emulex LP9002L, LP8000, LP7000E, LP952L and LP850 host bus adapters.
|
|
|
Standards
ANSI Fibre Channel
FC-FS
ANSI Fibre Channel FC-PH/PI
ANSI Fibre Channel FC-AL
ANSI Fibre Channel FC-PLDA
ANSI Fibre Channel FC-FLA
PCI Local Bus Revision 2.2
(see hardware requirements)
Fibre Channel Class 2, 3
PHP Hot plug - Hot swap
SW-2 switch standard
Architecture
(per channel)
Emulex Centaur ASIC technology
2Gb/s or 1Gb/s FC Link
2 MB FLASH memory
1 MB code RAM
128KB buffer RAM
Software Environments
Windows 2000
Windows NT
HP-UX
Linux
NetWare
AIX
Solaris x86
Hardware Environments
x86, SPARC and PowerPC
PCI hardware platforms
3.3V signaling, 5V tolerant
33/66MHz PCI
32/64 bit bus
Optical
| Data
Rates: |
1.0625/2.125 Gb/s |
| Optics: |
short/long wave
lasers |
| Cable: |
50/125 µm
multi-mode fiber |
| |
62.5/125 µm
multi-mode fiber |
| Connector: |
LC |
| Distance (1 Gb/s) |
500
meters (1640') 50/125 µm fiber |
| |
300
meters (984') 62.5/125 µm fiber |
| Distance (2 Gb/s) |
300 meters
(984') 50/125 µm fiber |
| |
150 meters
(492') 62.5/125 µm fiber |
|
Physical Dimensions
Short length PCI
Power Requirements
| Volts: |
+3.3 VDC (+/-5%) |
| Power
|
12.3 watts
typical (17.9 watts max) |
Environmental Conditions
|
Operating Temperature: |
0° to 45° C (32° to
113° F) |
|
Airflow required: |
100 lf/m |
| Storage
Temperature: |
-40° to 70° C (-40° to 158° F) |
| Relative
Humidity: |
5% to 95%
non-condensing |
Agency Approvals
| |
Class 1 Laser
Product per DHHS 21CFR (J)
and EN60825 |
| UL Recognized to
UL 1950 |
| CUR Recognized
to CSA22.2, No. 950 |
| TUV Certified to
EN60950 |
| FCC Rules, Part
15, Class A |
| ICES-003, Class
A |
| EMC Directive
89/336/EEC (CE Mark) |
| - EN55022,
Class A |
| - EN55024 |
| Australian EMC
Framework (C-Tick Mark) |
| -AS/NZS 3548,
Class A |
| VCCI, Class A |
| |
Ordering Information
|
LP9002DC-F2 |
Embedded
multi-mode
optic interface (LC) |
|
|
|
