|
HBA's & Switches
Emulex HBA's
 Sunstar Company
is proud to be an Emulex partner!
LP9002S 2Gb/s Fibre SBus Host
Bus Adapter
 |
Major Features
- Simultaneous full duplex 2Gb/s Fibre Channel delivers up to 400
MB/s
- Full fabric support using F_Port and FL_Port connections
- Onboard hardware context cache for superior fabric performance
- Support for concurrent use of multiple protocols (SCSI and IP)
- Support for FC service Classes 2 and 3
- Support for FC-Tape (FCP-2) devices
- 64-bit, SBus
- End-to-end parity protection for high data integrity
- Buffered data architecture to support up to 50km cabling at full
2Gb/s bandwidth
- Automatic speed negotiation
- Automatic topology detection
- Optical small form factor (LC) interface support
|
|
Optimized for Sun Microsystems SBus servers,the LightPulseTM
LP9002S Fibre Channel SBus host adapter provides support for 2Gb/s Fibre
Channel data rates,delivering the industry’s highest performance. The
LP9002S features automatic speed negotiation capability which allows
complete compatibility with existing 1Gb/s Fibre Channel Storage Area
Networks (SANs),while allowing seamless upgrades to higher speed 2Gb/s
SANs.
The LP9002S provides the flexibility and interoperability needed for
complex, highly scalable SANs. The LP9002S provides a unique combination
of features,including switched fabric support using F_Port and FL_Port
connections, full-duplex data transfers, high data integrity features,
support for all Fibre Channel topologies, and support for service class
2 and 3.
LP9002S also features sophisticated hardware that provides superior
performance in SANs, delivering low latency and high throughput in
switched, arbitrated loop and clustered environments. Support for fiber
optic cabling is provided through a small form factor (LC) optical
embedded interface.
The LightPulseTM LP9002S is complemented by robust
software support including multi-protocol (SCSI & IP) operation,
enabling advanced storage area network (SAN) implementations in Solaris
environments.The LP9002S Solaris driver shares a common source base with
drivers for the Emulex LP9002L, LP9000, LP8000, LP8000S and LP7000E PCI
host bus adapters, allowing a common look and feel across separate
hardware platforms.
|
|
|
Standards
ANSI Fibre Channel
FC-PH
ANSI Fibre Channel FC-AL
ANSI Fibre Channel FC-PLDA
ANSI Fibre Channel FC-FLA
Fibre Channel Class 2, 3
Architecture
Emulex Centaur ASIC
technology
512 KB FLASH memory
1 MB code RAM
128 KB buffer RAM
Software Environments
Solaris (Sparc)
Hardware Environments
Sun Enterprise (Ultra)
servers ES3500,
ES4500, ES5500, ES6500 and UE10K
Optical
| Data
Rate: |
1.0625/2.125 Gb/s |
| Optics: |
short wave
lasers |
| |
50/125 µm
multi-mode fiber |
| |
62.5/125 µm
multi-mode fiber |
| Connector Type: |
LC |
| Distance (1Gb/s) |
500
meters (1640') 50/125 µm fiber |
| |
300
meters (984') 62.5/125 µm fiber |
| Distance (2 Gb/s) |
300 meters
(984') 50/125 µm fiber |
| |
150 meters
(492') 62.5/125 µm fiber |
|
Physical Dimensions
SBus single-width form
factor 146.7mm x 83.82mm
(5.78" X 3.3")
Power Requirements
| Volts: |
+5 VDC, +/-12VDC
@ 15ma |
| Power
|
6.9 watts
typical (10w max) |
Environmental Conditions
|
Operating Temperature: |
0° to 45° C (32° to
113° F) |
| airflow
required: |
100 lfm |
| Storage
Temperature: |
-40° to 70° C (-40° to 158° F) |
| Relative
Humidity: |
5% to 95%
non-condensing |
Agency Approvals
Class 1 Laser
Product per DHHS 21CFR (J)
and EN60825 |
| UL Recognized to
UL 1950 |
| CUR Recognized
to CSA22.2, No. 950 |
| TUV Certified to
EN60950 |
| FCC Rules, Part
15, Class A |
| Industry Canada,
ICES-003, Class A |
| EMC Directive
89/336/EEC (CE Mark) |
| - EN55022,
Class A |
| - EN55024 |
| Australian EMC
Framework (C-Tick Mark) |
| -AS/NZS 3548,
Class A |
| VCCI, Class A |
| |
Ordering Information
| LP9002S-F2 |
Embedded
multi-mode optic interface (LC) |
|
|
|
