|
HBA's & Switches
Emulex HBA's
 Sunstar Company
is proud to be an Emulex partner!
LP9402DC 2Gb/s Dual Fibre Channel PCI-X Host
Bus Adapter
 |
Major Features
- Full duplex 2 Gb/s Fibre Channels deliver up to 800MB/s link
bandwidth
- Automatic speed negotiation
- Full fabric support using F_Port and FL_Port connections
- Onboard hardware context cache for superior fabric performance
- Support for multiple protocols (SCSI and IP)
- Full support for FC service class 2 and 3
- Support FC-Tape (FCP-2) devices
- 64-bit PCI-X 1.0a and PCI 2.2 compatibility
- End-to-end parity protection for high data integrity
- Robust suite of software including IP and storage protocols under
Windows 2000, Windows NT, Linux, NetWare, AIX and Solaris
- Optical small form factor (LC) interface support
|
|
Description The LP9402DC Dual
Channel PCI-X host bus adapter offers two independent 2Gb/s Fibre
Channel HBA interfaces in a single PCI-X slot. It delivers exceptional
performance through the use of two Emulex Centaur ASICs, two 266MIPS
onboard processors, high speed buffer memory. The LP9402DC features
automatic speed negotiation capability which allows complete
compatibility with existing 1Gb/s Fibre Channel SANs, while allowing
seamless upgrades to higher speed 2Gb/s SANs.
The LP9402DC architecture is based on two of Emulex's high
performance 2Gb/s HBAs integrated into one board with a PCI-X bridge to
provide bus compatibility with PCI-X or PCI 2.2 based systems. This
provides the flexibility and broad interoperability needed for complex,
highly scalable SANs. The LP9402DC provides a combination of features,
including switched fabric support using F_Port and FL_Port connections,
full-duplex data transfers, high data integrity features, support for
all Fibre Channel topologies and support for service classes 2 and 3, in
a dual channel HBA.
The LP9402DC also features sophisticated hardware that provides
superior performance in SANs, delivering low latency and high throughput
in switched fabric, arbitrated loop and clustered environments. Support
for fiber optic cabling is provided through embedded small form factor
(LC) optical interfaces.
Driver Support
A rich suite of software support complements the LP9402DC, including
storage protocol (SCSI), network protocol (IP) and multi-protocol (SCSI
& IP) operation. These enable advanced storage area network (SAN)
implementations in Windows 2000, Windows NT, Linux, NetWare, AIX and
Solaris environments. All drivers are also fully compatible with the
Emulex LP9002L, LP8000, LP8000DC, LP7000E, LP952L and LP850 host bus
adapters.
|
|
|
Standards
ANSI Fibre Channel
FC-FS
ANSI Fibre Channel FC-PH/PI
ANSI Fibre Channel FC-AL
ANSI Fibre Channel FC-PLDA
ANSI Fibre Channel FC-FLA
PCI-X 1.0a
PCI Local Bus Revision 2.2
(see hardware requirements)
Fibre Channel Class 2, 3
PHP Hot plug - Hot swap
Architecture
(per channel)
Emulex Centaur ASIC technology
2Gb/s or 1Gb/s FC Link
2 MB FLASH memory
1 MB code RAM
128KB buffer RAM
Software Environments
Windows 2000
Windows NT
Linux
NetWare
AIX
Solaris x86
Hardware Environments
x86, SPARC and PowerPC
PCI hardware platforms
3.3V signaling
up to 66MHz PCI
up to 133MHz PCI-X
Optical
| Data
Rates: |
1.0625/2.125 Gb/s |
| Optics: |
short wave
lasers |
| Cable: |
50/125 µm
multi-mode fiber |
| |
62.5/125 µm
multi-mode fiber |
| Connector: |
LC |
| Distance (1 Gb/s) |
500
meters (1640') 50/125 µm fiber |
| |
300
meters (984') 62.5/125 µm fiber |
| Distance (2 Gb/s) |
300 meters
(984') 50/125 µm fiber |
| |
150 meters
(492') 62.5/125 µm fiber |
|
Physical Dimensions
Short length PCI
Power Requirements
| Volts: |
+3.3 VDC (+/-5%) |
| Power
|
13.8 watts
typical (18 watts max) |
Environmental Conditions
|
Operating Temperature: |
0° to 45° C (32° to
113° F) |
|
Airflow required: |
100 lf/m |
| Storage
Temperature: |
-40° to 70° C (-40° to 158° F) |
| Relative
Humidity: |
5% to 95%
non-condensing |
Agency Approvals
| |
Class 1 Laser
Product per DHHS 21CFR (J)
and EN60825 |
| UL Recognized to
UL 1950 |
| CUR Recognized
to CSA22.2, No. 950 |
| TUV Certified to
EN60950 |
| FCC Rules, Part
15, Class A |
| ICES-003, Class
A |
| EMC Directive
89/336/EEC (CE Mark) |
| - EN55022,
Class A |
| - EN55024 |
| Australian EMC
Framework (C-Tick Mark) |
| -AS/NZS 3548,
Class A |
| VCCI, Class A |
| |
Ordering Information
| LP9402DC-F2 |
Embedded
multi-mode
optic interface (LC) |
|
|
|
