|
HBA's & Switches
Emulex HBA's
 Sunstar Company
is proud to be an Emulex partner!
LP9802DC 2Gb/s Dual Fibre Channel PCI-X Host
Bus Adapter
 |
Major Features
- two full duplex 2Gb/s Fibre Channels deliver up to 800MB/s link
bandwidth
- automatic speed negotiation
- automatic topology detection
- full fabric support using F_Port and FL_port connections
- onboard hardware context cache for superior fabric performance
- support for multiple concurrent protocols (SCSI and IP)
- full support for both FC service class 2 and 3
- full fabric boot support in x86 and SPARC environments to multiple
LUNs
- support for FCP-2 (FC-Tape) devices
- 66/100/133 MHz PCI-X 1.0a and PCI 2.2 compatibility
- end-to-end parity protection for high data integrity
- robust suite of software including IP and storage protocols under
Windows 2000, Windows NT, Linux, NetWare, HP-UX and Solaris
- optical small form factor (LC) interface
|
|
Description The LP9802DC Dual Channel PCI-X host bus adapter
offers two independent 2Gb/s Fibre Channel HBA interfaces in a single
PCI-X slot. It delivers exceptional performance through the use of two
Emulex Pegasus ASICs, two 266MIPS onboard processors and high speed
memory. The LP9802DC features auto-matic speed negotiation, which allows
complete compatibility with existing 1Gb/s Fibre Channel SANs, while
allowing seamless upgrades to higher speed 2Gb/s SANs.
The LP9802DC provides the functionality of two of Emulexˇ¦s high
perfor-mance PCI-X 133 MHz HBAs integrated onto one board, which
provides bus compatibility with PCI-X or PCI 2.2 based systems. This
provides the flexibility and broad interoperability needed for complex,
highly scalable SANs. The LP9802DC provides a combination of features,
including switched fabric support using F_Port and FL_Port connections,
full-duplex data transfers, high data integrity features, support for
all Fibre Channel topologies, and support for service classes and , in a
dual channel HBA.
The LP9802DC also features sophisticated hardware that provides
superior performance in SANs, delivering low latency and high throughput
in switched fabric, arbitrated loop and clustered environments. Support
for fiber optic cabling is provided through an embedded small form
factor (LC) optical interface.
Driver Support
A rich suite of software complements the LP9802DC. Some examples of
the features included are: LUN Masking, LUN Mapping, Persistent Binding,
I/O Coalescing, full fabric boot in x86, Intel® Itanium® processor
family and SPARC environments, as well as support for simultaneous
protocol (SCSI & IP) opera-tion. In addition, most drivers include a
full-featured implementation of the FC-MI HBA Management API interface.
These features enable advanced storage area network (SAN)
implementations in Windows 2000, Win-dows NT, Linux, HP-UX, Solaris and
NetWare environments. Supported drivers are also fully compatible with
the Emulex LP9802, LP9002L, LP8000, LP7000E, LP9402DC, and LP9002DC host
bus adapters. Windows, Linux and NetWare drivers are also compat-ible
with the LP850, LP952L and LP982.
|
|
|
standards
ANSI Fibre Channel
FC-FS
ANSI Fibre Channel FC-PH
ANSI Fibre Channel FC-PI
ANSI Fibre Channel FCP
ANSI Fibre Channel FCP-2
IETF IP over FC
ANSI Fibre Channel FC-AL
ANSI Fibre Channel FC-PLDA
ANSI Fibre Channel FC-MI
ANSI Fibre Channel FC-FLA
PCI-X 1.0a
PCI local bus revision 2.2 (see hardware requirements)
Fibre Channel Class 2, 3
PHP hot plug - hot swap
architecture
Emulex Pegasus ASIC
technology
2Gb/s or 1Gb/s FC Link
2MB FLASH memory
1MB unified QDR memory
software environments
Windows 2000
Windows NT
Linux
HP-UX
NetWare
Solaris
hardware environments
Intel® Itanium®
Processor Family
x86, SPARC and PowerPC
32/64b 33/66MHz PCI
3.3v signaling
66/100/133MHz PCI-X
optical
|
data
rate: |
1.0625/2.125Gb/s |
|
optics: |
short
wave lasers |
|
cable: |
50/125µm multi-mode fiber |
| |
62.5/125µm multi-mode fiber |
|
connector: |
LC |
|
distance: |
(1Gb/s) |
| |
500
meters (1,640') 50/125 µm fiber |
| |
300
meters (984') 62.5/125 µm fiber |
| |
(2Gb/s) |
| |
300
meters (984') 50/125 µm fiber |
| |
150
meters (492') 62.5/125 µm fiber |
|
physical dimensions
short length PCI
power requirements (PCI-X
133MHz)
|
volts: |
+3.3
VDC (± 5%), 1.2A typ. 1.7A max.
+5 VDC (±5%), 2.0A typ. 2.9A max. |
|
power: |
14.0W
typ., 20.1W max. |
environmental conditions
|
operating temperature: |
0° to
45°C (32° to 113°F) |
|
airflow required: |
100
lf/m |
storage temperature
-40° to 70°C (-40° to
158°F)
relative humidity
5% to 95%
non-condensing
Agency Approvals
Class 1 Laser Product
per DHHS 21CFR (J) & EN60825
UL recognized to UL 1950
CUR recognized to CSA22.2, No. 950
TUV certified to EN60950
FCC rules, Part 15, Class A
ICES–003, Class A
EMC Directive 89/336/EEC (CE Mark)
EN55022, Class A
EN55024
Australian EMC Framework (C–Tick Mark)
AS/NZS 3548, Class A
VCCI, Class A
Ordering Information
|
LP9802DC–F2 |
embedded multi-mode optic interface (LC)
|
This document refers
to various companies and products by their trade names. In most, if not
all cases, their respective companies claim these designations as
trademarks or registered trademarks. This information is provided for
reference only. Although this information is believed to be accurate and
reliable at the time of publication, Emulex assumes no responsibility
for errors or omissions. Emulex reserves the right to make changes or
corrections without notice. |
|
|
